Uncategories Konfigurasi Vlan di Cisco Packet Tracer

Konfigurasi Vlan di Cisco Packet Tracer

Cara membuat Vlan Di Cisco memang agak Susah tapi kalau Terus coba pasti terasa muda, Kalian yang ingin mencoba bisa mengikuti caranya Di Bawah ini.

Topologi

Konfigurasi Di Router

Router>en

Router#vla

Router#vlan da

Router#vla

Router#vlan dat

Router#vlan database

Router(vlan)#vlan 10 na

Router(vlan)#vlan 10 name kacrut

VLAN 10 added:

Name: kacrut

Router(vlan)#vlan 20 na

Router(vlan)#vlan 20 name kucrut

VLAN 20 added:

Name: kucrut

Router(vlan)#exit

APPLY completed.

Exiting....

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#int fa0/1.10

Router(config-subif)#enca

Router(config-subif)#encapsulation d

Router(config-subif)#encapsulation dot1Q 10

Router(config-subif)#ip add

Router(config-subif)#ip address 10.10.10.1 255.255.255.0

Router(config-subif)#no sh

Router(config-subif)#exit

Router(config)#int fa0/1.20

Router(config-subif)#emc

Router(config-subif)#enc

Router(config-subif)#encapsulation do

Router(config-subif)#encapsulation dot1Q 20

Router(config-subif)#ip add

Router(config-subif)#ip address 20.20.20.1 255.255.255.0

Router(config-subif)#no sh

Router(config-subif)#exit

Router(config)#exit

Router#wr

Building configuration...

[OK]

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#int

Router(config)#interface fa0/1

Router(config-if)#no sh

%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

%LINK-5-CHANGED: Interface FastEthernet0/1.10, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1.10, changed state to up

%LINK-5-CHANGED: Interface FastEthernet0/1.20, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1.20, changed state to up

Router(config-if)#exit

Router(config)#exit

Router#

Router#vl

Router#vlan dat

Router#vlan database

Router(vlan)#vlan 2 name sw

VLAN 2 added:

Name: sw

Router(vlan)#exit

APPLY completed.

Exiting....

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#int fa0/1

Router(config-if)#exit

Router(config)#int fa0/1.2

Router(config-subif)#encapsulation dot1Q 2

Router(config-subif)#ip address 2.2.2.1 255.255.255.252

Router(config-subif)#no sh

Router(config-subif)#des "to-sw"

Router(config-subif)#exit

Konfigurasi Switch

Switch

Switch>EN

Switch#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#int fa0/1

Switch(config-if)#sw

Switch(config-if)#switchport mode

Switch(config-if)#switchport mode tr

Switch(config-if)#switchport mode trunk

Switch(config-if)#no sh

Switch(config-if)#exit

Switch(config)#end

Switch#

%SYS-5-CONFIG_I: Configured from console by console

Switch#vla

Switch#vlan dat

Switch#vlan database

% Warning: It is recommended to configure VLAN from config mode,

as VLAN database mode is being deprecated. Please consult user

documentation for configuring VTP/VLAN in config mode.

Switch(vlan)#vlan 10 na

Switch(vlan)#vlan 10 name kacrut

VLAN 10 added:

Name: kacrut

Switch(vlan)#vlan 20 na

Switch(vlan)#vlan 20 name kucrut

VLAN 20 added:

Name: kucrut

Switch(vlan)#exit

APPLY completed.

Exiting....

Switch#sh vla

Switch#sh vlan

Switch#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#int fa0/2

Switch(config-if)#sw

Switch(config-if)#switchport mode ac

Switch(config-if)#switchport mode access

Switch(config-if)#sw

Switch(config-if)#switchport av

Switch(config-if)#switchport ac

Switch(config-if)#switchport access vl

Switch(config-if)#switchport access vlan 10

Switch(config-if)#no sh

Switch(config-if)#des

Switch(config-if)#des

Switch(config-if)#description "kacrut"

Switch(config-if)#exit

Switch(config)#int fa0/3

Switch(config-if)#sw

Switch(config-if)#switchport mo

Switch(config-if)#switchport mode ac

Switch(config-if)#switchport mode access

Switch(config-if)#sw

Switch(config-if)#switchport ac

Switch(config-if)#switchport access vl

Switch(config-if)#switchport access vlan 20

Switch(config-if)#no sh

Switch(config-if)#des "kucrut"

Switch(config-if)#exit

Switch(config)#end

Switch#

%SYS-5-CONFIG_I: Configured from console by console

Switch#wr

Building configuration...

[OK]

Switch#

%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Switch#vl

Switch#vlan da

Switch#vlan database

Switch(vlan)#vla

Switch(vlan)#vlan 2 na

Switch(vlan)#vlan 2 name to-ro

VLAN 2 added:

Name: to-ro

Switch(vlan)#exit

APPLY completed.

Exiting....

Switch#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#int vla

Switch(config)#int vlan 2

%LINK-5-CHANGED: Interface Vlan2, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan2, changed state to up

Switch(config-if)#no sh

Switch(config-if)#ip ad

Switch(config-if)#ip address 2.2.2.2 255.255.255.252

Switch(config-if)#no sh

Switch(config-if)#ex

Switch(config)#ip def

Switch(config)#ip default-gateway 2.2.2.1

Switch(config)#exit

Author : Unknown

Share this

Langganan: Posting Komentar (Atom)